Progress Menu
x
Home / Add-on / Garments, Jackets and Coats, Outerwear
This pattern is copyrighted 2022 to Rebecca Page by app.youmakehq.com
Please feel free to make garments from this pattern to sell. If you do, we would love you to include a credit to app.youmakehq.com as the pattern designer, but it is up to you.
The finished product may only be sold by crafters. It may not be mass produced. You can only sell the finished product; you cannot sell the pattern or these instructions.
Best of luck and happy sewing!
10
![]()
![]()
Add On Kingston Sewing Pattern
Member Rating
Difficulty Level
Advanced Beginner
Equipment Needed
Description
This pattern is a fun update to your denim jacket with the option of knit sleeves and hood, welt pockets, an internal pocket and back ruffle. As this is an add on, you will need the Women’s 1-10, Women’s Curvy 6C-15C, newborn-12yrs, or 18-inch doll Kingston Sewing Pattern to make use of the add on.
Not a member yet? Click here to sign up
- +Preparation
- For optional Hood:
- 1-2 yards of shoe string, cording or other tie option.
- Grommets can be used in place of buttonholes, if desired
- Thread to match
- Option A: Back Frill
- Back Frill – Fabric cut 1
- All chosen options from the original pattern cutting checklist
- Option B: Single Welt Pocket
- Welt Pocket – Fabric cut 4
- Welt Pocket Bag – Lining cut 4 (2x mirror image)
- All chosen options from the original pattern cutting checklist
- Note: there is a pattern piece for the front side. This is the same as the original, but includes placement lines for the welt Pocket
- Note: Inseam Pockets are not compatible with welt Pockets
- Option C: Inside Pocket
- Inside Pocket – Fabric cut 2
- All chosen options from the original pattern cutting checklist
- Note: Inside Pocket is compatible with either the welt Pocket or the inseam Pocket
- Option D: Knit Sleeves
- Knit Sleeves – Fabric cut 2 (1x mirror image)
- Knit Sleeve Cuffs – Fabric cut 2
- All chosen options from the original pattern cutting checklist EXCEPT sleeves
- Option E: Knit Hood
- Hood – Fabric cut 2 (1x mirror image)
- All chosen options from the original pattern cutting checklist EXCEPT collar pieces
- Use a ball point needle of a size appropriate to your fabric when working with knits – The ball point needle has a slightly rounded tip and will prevent from damaging the fibre. Use ball point pins or clips and, if you can’t, use regular pins into the seam allowance and you should be just fine.
- Use a stretch stitch – You can use either a short and narrow zigzag or a stretch stitch (lightning bolt stitch) for construction. Test on a scrap of fabric to find which stitch and tension settings work best for you. You don’t want the fabric to pucker under your stitches.
- Your machine might have many fancy stretch stitches and you are welcome to play with them, but often the basic zigzag or stretch stitch are just right.
- Use a walking foot – Using a walking-foot is not a necessity but it is highly recommended when working on a stretchy knit. The walking-foot helps to prevent one layer of fabric from stretching out while sewing. Both layers of fabrics are fed at the same time under your needle.
- Reduce your presser foot tension – Some machines will allow you to change your presser foot tension. Check your manual to see how to reduce your presser foot tension. Reducing tension will prevent your fabric from stretching while it goes through the machine.
- Use a ball point twin-needle (double needle) for top stitching – Using a twin-needle will give you a regular double line of straight stitches on the right side and a short and stretchy zigzag on the wrong side. Alternatively, if you don’t own a twin needle, you can use a medium size zigzag stitch for hemming and topstitching. I like to lengthen my stitch a little when top stitching with the twin needle. Test on a scrap of fabric to find what works best for you.
- Finishing the seams – Because knits don’t fray, it isn’t strictly necessary to finish your seams. That being said, you will achieve a more polished and durable look if you do an overcasting or zigzag stitch on your raw edges.
Project OverviewKingston Jacket Add-On
Difficulty Level = Beginner / Intermediate
There are 5 different options included in this add-on pattern. You can choose any or all of these options for your jacket. Mix and match to get the jacket you are looking for!
The back ruffle is a small change that requires no change to the original pattern, just a slight pause and add a few steps during construction.
The Hood is added in place of your collar pieces. But is compatible with all other options in the original and add-on pack.
The knit sleeves are obviously in place of all other sleeve options, but pair well with the Hood and any of the Pocket choices.
The two new Pockets include an inside Pocket and a welt Pocket. The inside Pocket is compatible with both the original inseam Pocket and the welt Pocket. The welt Pocket and the inseam Pocket do not work together. Neither additional Pocket interferes with the chest Pocket from the original pattern.
Between the original pattern and this add-on pack, there are so many choices for gorgeous jackets with beautiful construction and we can’t wait to see what you make up!
NOTE – The sewing instructions and steps are the same for all sizes (dolls, child’s, and ladies sizes).
Our Facebook group is a great place to get help, share your tips and creations! We are a friendly bunch, and we love to help and see what you have made.
Please read the full instructions before getting started.
Wash, dry, and press your fabric before starting your project. A bit of prep now prevents shrinking and means your garment will stay the same size you made it.
Never leave a child or baby unattended or allow to sleep in a garment made from one of our patterns with ties, snaps, buttons, or anything they could remove, choke on, or get caught on. Always use caution if you are unsure. We love our patterns, but we love your bundles of joy more!
SizingSize Range
18 in Dolls, Newborn – 12yrs, Womens 1-10, Womens Curvy 6C-15C
Size Chart
See the original Kingston Jacket pattern for the sizes available and finished garment measurements.
Finished Measurements (Inches)
See the original Kingston Jacket pattern for finished garment measurements.
Fitting NotesBe sure to check the original Kinston Jacket pattern for applicable fitting notes to get the best fit from your Kingston Jacket.
Materials and ToolsYou will need the following, in addition to the listed requirements in the original Kingston Jacket pattern.
Fabric Requirements 60 inches/150 cm wide (in YARDS)
Frill
Knit Sleeve
Knit Hood
Welt Pocket
Inside Pocket
1-6
0.25
0.75
0.75
0.25
0.25
7-10
0.25
0.75
0.75
0.25
0.25
Frill Knit Sleeve Knit Hood Welt Pocket Inside Pocket 6C-11C 0.25 0.75 0.75 0.25 0.25 12C-15C 0.25 0.75 0.75 0.25 0.25 * If you are using a narrower fabric, a directional print, or a fabric with nap you may need more.
** Make sure to wash, dry, and press all fabrics before cutting out in case they shrink.You will also need:
Tools needed are listed in the original Kingston Jacket pattern.
Printing Your PatternSettings
The pattern is a separate download. Choose either the US letter paper, A4 paper, or A0 paper size based on the printer you wish to use. If you are in the US or Canada then your printer will likely use US letter paper. Other regions normally use A4 paper. Some people prefer to print their patterns at a print shop: A0 is best in this case.
Print at 100%.
On the second page, you will find a 1-inch and a 3-inch square test box. Print this page first, on its own, and measure these squares.
Once you are happy that the test box is accurate, print the rest of the pattern pages.
Please follow this video for information and assistance on assembling this pattern.
Also, please note that some Rebecca Page patterns and projects also come with cut files and a printable design page which you can use to plan your project if you wish. These are provided in a separate section below to avoid any confusion!
+US Print Charts
Here are which pages to print for the US Files
Hood Sleeves Frill Pockets Welt Inside 1 – 5 8-9, 13-14 2-6, 10-12, 15-17 4-6 18, 21-23 19-20 6 – 10 8-9, 13-14 2-6, 10-12, 15-17 4-7 18, 21-23 19-20 Hood Sleeves Frill Pockets Welt Inside 6C 6-7, 12-13 2-4, 8-10, 15-16, 20-21 2-6 11, 17-19, 24-25 22-23 7C – 8C 6-7, 12-13 2-4, 8-10, 14-16, 20-21 2-6 11, 17-19, 24-25 22-23 9C – 12C 6-7, 12-13 2-4, 8-11, 14-16, 20-21 2-6 11, 17-19, 24-25 22-23 13C – 15C 6-7, 12-13 2-5, 8-11, 14-16, 20-21 2-6 11, 17-19, 24-25 22-23 Hood Sleeves Frill Pockets Welt Inside 0 – 6 mos 3-4 2-3. 7 5, 10 7-9 9 6 – 24 mos 3-4 2-3, 7-8 5, 10 7-9 9 2 – 6 yrs 19-20 12-14, 17-18 5, 10 5, 7, 10, 16 15 7 – 8 yrs 19-20 12-14, 17-18 5, 10 5, 7, 10, 16 15-16 9 – 12 yrs 19-20 12-14, 17-18 5, 10 5-7, 10-11, 16 15-16 Hood Sleeves Frill Pockets Welt Inside Dolls 4 2 3 3-4 3 +A4 Print Charts
Here are which pages to print for the A4 Files
Hood Sleeves Frill Pockets Welt Inside 1 – 3 8-9, 14-15 2-3, 5-6, 11-13, 17-19 4-6 10, 16, 22-23 20-21 4 – 6 8-9, 14-15 2-3, 5-6, 11-13, 17-19 4-7 10, 16, 22-23 20-21 7 – 10 8-9, 14-15 2-3, 5-6, 11-13, 17-19 4-7 10, 16, 22-24 20-21 Hood Sleeves Frill Pockets Welt Inside 6C – 7C 6-7, 12-13 2-4, 8-10, 14-16, 20-21 2-6 11, 17-19, 24-25 22-23 8C 6-7, 12-13 2-5, 8-10, 14-16, 20-21 2-6 11, 17-19, 24-25 22-23 9C – 13C 6-7, 12-13 2-5, 8-11, 14-16, 20-21 2-6 11, 17-19, 24-25 22-23 14C – 15C 5-7, 12-13 2-5, 8-11, 14-16, 20-21 2-6 11, 17-19, 24-25 22-23 Hood Sleeves Frill Pockets Welt Inside 0 – 18 mos 3-4 2-3. 7 5, 10 7-9 9 18 – 24 mos 3-4 2-3, 7-8 5, 10 7-9 9 2 – 3 yrs 20-21 12-13, 17-19 5, 10 5, 10, 14, 16 15 3 – 4 yrs 20-21 12-13, 17-19 5, 10 5-6, 10-11, 14, 16 15 9 – 12 yrs 20-21 12-13, 17-19 5, 10 5-6, 10-11, 14, 16 15-16 Hood Sleeves Frill Pockets Welt Inside Dolls 4 2 3 3-4 3 Cutting InstructionsCut each of the pieces according to the directions on the pattern piece. Seam allowances are all included so just cut them as is.
Cutting Charts – All pattern pieces are included, however if you prefer to cut using a cutting chart, the dimensions for the rectangular pieces are below:
Welt Pocket
(cut 4)
Back Frill (cut 1)
Width
Length
Width
Length
1
6.75
2.50
20.75
2.00
2
6.75
2.50
21.50
2.00
3
7.00
2.50
22.25
2.00
4
7.00
2.50
23.00
2.00
5
7.25
2.50
23.50
2.00
6
7.25
2.50
24.75
2.00
7
7.50
2.50
25.75
2.00
8
7.50
2.50
26.75
2.00
9
7.75
2.50
27.75
2.00
10
7.75
2.50
28.75
2.00
Welt Pocket (cut 4)
Back Frill (cut 1) Width Length Width Length 6C 7.2 2.50 26.5 2.00 7C 7.3 2.50 27.7 2.00 8C 7.4 2.50 27.7 2.00 9C 7.5 2.50 28.3 2.00 10C 7.6 2.50 29.0 2.00 11C 7.7 2.50 29.6 2.00 12C 7.8 2.50 30.2 2.00 13C 8.0 2.50 31.0 2.00 14C 8.1 2.50 31.5 2.00 15C 8.2 2.50 32.0 2.00 Cutting Checklist:
You will need to choose your options from the original Kinston Jacket pattern as well as any add-ons you would like to include.
NOTE – To cut fabric on the fold, fold your fabric over parallel to the selvage edges. Align the pattern piece so it is on the fold of the fabric. Cut around the edges, leaving the fold. If you have folded your fabric correctly the fold will be parallel to the two edges of the fabric that are finished. The raw edges (e.g. the ones you could pick at and threads would come off) will be at a right angle to your fold.
Fabric TipsTips for Sewing with Knit Fabrics
Using a serger is not a necessity to sew with knit fabrics! Here are a few tips to get the best results on a regular sewing machine:
Here is an example of some of the stitches you could use.
From left to right: Ballpoint twin-needle, narrow zigzag, stretch stitch (lightning bolt), overcasting.
- For optional Hood:
- + Instructions
- INSIDE POCKET CONSTRUCTION – Serge top edge. Turn down ½ inch and press. Topstitch ¼ inch from top edge and again the same distance as the flat fell seams from the original pattern. Position Pocket inside jacket, wrong sides together, aligning raw edges of side and bottom. Pin across front flat fell seams, pointing pins in. This will get attached during the regular construction of your Kingston.
- OPTIONAL PEN SLOTS – Before step 1.4 from the original pattern, follow the above steps for the inside Pocket, then continue on to step 1.4. This will segment the Pocket into pen slots.
- POCKET PREPARATION – Serge all edges of Pocket bag pieces. Transfer welt Pocket sewing lines to Pocket lining piece. Right sides together, align Pocket lining on front of jacket. Sew along rectangle marking. Draw a straight line down the center of the rectangle, stopping ½ inch from each edge. Cut along this line, through both layers, then toward all four corners. Push lining to wrong side of jacket and press.
- POCKET CONSTRUCTION – Fold welt piece in half and serge raw edges. Place welt on wrong side of jacket front, aligning folded edge with top edge of the Pocket opening. From the right side, pin in place. Top stitch all four sides of opening. Right sides together, align Pocket exterior with Pocket lining and sew.
- FRILL PIECE PREPARATION – Complete steps 4.1-4.3 from original pattern. Turn bottom edge of Frill piece ¼ inch, twice and topstitch. Repeat for both short edges. Baste and gather top edge.
- ATTACH THE FRILL – On both ends of the yoke seam, measure ⅝ inch from edge and mark. Place Frill right side up under the yoke seam allowance, butting each end up to the marks you made. Adjust gathers, pin and topstitch close to the folded edge.
- PREPARING THE HOOD – Right sides together, serge center seam of Hood. Serge front raw edge without trimming. Mark, stabilize then add your buttonholes.
- ATTACH THE HOOD – Right sides together, align center back of jacket with center seam of Hood. Align facing markers of Hood with seam allowance cut line. Pin and serge Hood, including the end of the Hood that is not attached to the jacket. Press seam allowance down and topstitch. Fold Hood facing in, wrong sides together with Hood. Thread your drawstring through your buttonhole and tucked into facing. Stitch facing closed with twin needle or zig-zag stitch.
- SLEEVE CONSTRUCTION – pin and sew the sleeves to the jacket. Press seam toward jacket front and topstitch. Sew arm and side seams.
- ATTACH THE CUFF – Fold cuff in half and serge. Fold in half, wrong sides together and attach to sleeves.
Quick Glance Cheat Sheet⅝ inch seam allowance included – Top stitching ⅛ inch – Basting ¼ inch
Option A – Inside Pocket
Option B – Single Welt Pocket
Option C – Back Frill
Option D – Knit Hood
Option E – Knit Sleeves
0 . PreparationSeam Allowance
⅝ inch seam allowance included – Basting ¼ inch – Top stitching ⅛ inch
0.0Complete all of step 1 from the original pattern before beginning inside Pocket construction.
1 . Inside Pocket Construction1.1Serge or use an overcast stitch on your sewing machine on the top raw edge.
1.2Fold the top down ½ inch and press.
1.3Top stitch ⅛ inch from top folded edge, then at the same distance as the flat fell seams on the front of the jacket.
1.4Position the Pocket to the inside of your jacket, wrong sides together, lining up the raw edges of the Pocket piece with the raw edges of the jacket at the side seam and the bottom of the jacket. Place pins centered over the flat fell seams and away from the edges.
The raw edges will be enclosed by the front placket, side seam and the waistband. At step 13.14 of the original Kingston tutorial ensure that the Pocket pieces are within the waistband so that the top stitching closes the bottom of the inside Pocket.
2 . Optional Pen Slots2.1Before completing step 1.4 of the Original Kingston tutorial, follow the steps of the internal Pocket and then continue to step 1.4. The top stitching of the flat fell seam will create a segmented Pocket to place a pen.
0 . PreparationSeam Allowance
⅝ inch seam allowance included – Basting ¼ inch – Top stitching ⅛ inch
0.0Complete all of step 1 from the original pattern before beginning welt Pocket construction.
Note: There are many ways to sew a welt Pocket. Feel free to use a method you are comfortable with. No matter what method you use, the most important thing is accuracy in your sewing. Ensure your lines are parallel and your starting and finishing point is exactly in the same spot to ensure your rectangle is perfectly square.
To keep the raw edges clean and tidy we are going to serge the raw edges in this option. If you don’t have a serger use an overcast stitch on your machine.
1 . Pocket Preparation1.1Serge all raw edges of the Pocket bag pieces.
1.2Transfer the welt Pocket sewing lines from the pattern piece to the wrong side of the Pocket lining piece.
1.3Place the Pocket lining piece on the right side of the jacket (right sides together), matching up the welt Pocket placement on the front side panel of the jacket.
1.4Sew all the way round the rectangle, remembering to keep all lines parallel and your starting and finishing point is in exactly the same spot.
1.5Draw a straight line down the center of the rectangle, starting and stopping ½ inch either side of the stitches.
1.6Cut along that line, through both layers, then at each end cut diagonally to the corners, cutting as close you can to the corners without cutting the stitches.
1.7Push the Pocket lining through the cut to the wrong side of the jacket. Flatten the Pocket lining out and then press.
2 . Pocket Construction2.1Time to sew the welt. Fold your welt piece in half lengthways, wrong side together. Press then serge all raw edges, without cutting off any fabric.
2.2On the wrong side of the jacket place the folded edge of the welt piece centered in line with the top edge of the Pocket opening.
2.3On the right side of the jacket, pin the welt piece in place, ensuring that the welt completely sits within the Pocket opening and the long side closest to the side seam is left open.
2.4Top stitch the opening of the Pocket around all four sides.
2.5Turn the jacket over to the wrong side. You should have your welt sewn to the lining of the Pocket.
2.6Place the exterior Pocket bag piece on the lining piece with right sides together. Pin.
1 . Frill Piece PreparationSeam Allowance
⅝ inch seam allowance included – Basting ¼ inch – Top stitching ⅛ inch
1.1Complete steps 4.1 to 4.3 from the original Kingston instructions.
Turn the bottom edge of the Frill piece under ¼ inch then press. Turn under another ¼ inch and press again.
1.2Stitch as close as possible to the top edge.
Repeat for both short edges.
1.3Now we need to create the Frill. Increase your stitch length and sew a row of gathering stitches just under ¼ inch from the raw edge and ¼ inch from the start and finish ¼ inch from the end. Gather by pulling the bobbin thread.
2 . Attach the Frill2.1Now it’s time to attach the Frill. Starting with the back piece measure along the yoke seam ⅝ inch and mark with a pin, repeat at the other end.
2.3Topstitch close to the folded edge. Go slowly to get through all the layers. If need be, use the hand wheel.
0 . PreparationSeam Allowance
⅝ inch seam allowance included – Basting ¼ inch – Top stitching ⅛ inch
0.0Complete all construction through step 6 from the original Kinston pattern prior to adding your knit Hood.
1 . Preparing the Hood1.0SERGER / OVERLOCKER OPTION – We will be using a serger for this option
REGULAR SEWING MACHINE OPTION – Use an overcast stitch instead of serging and follow the steps below.
1.2Serge the front raw edge, without trimming any fabric. This step is just to finish the raw edge.
1.3Using the pattern piece as a guide, and an erasable pen, mark the buttonhole position for the drawstring where the small circle is on the pattern piece.
If you’d prefer to use grommets, feel free to add them here according to manufacturer’s instructions. Then skip to step 2.
If you’d prefer to make a buttonhole, continue to step 1.4 Your buttonhole should be centered vertically over this circle marking.
1.4It is important to stabilize knit fabric before sewing the buttonhole. I have used some scrap pieces of denim and attached it to the wrong side of the Hood with fabric glue. If you do not stabilize your fabric, it may bunch up and get stuck in the feed dogs.
1.5Time to do your buttonhole.
2 . Attach the Hood2.0SERGER / OVERLOCKER OPTION – We will be using the serger for this step.
REGULAR SEWING MACHINE OPTION – Use an overcast stitch instead of serging and follow the steps below.
2.1Find the center point of the back of the jacket and mark with a pin.
Using the pattern piece as a guide, mark the Hood piece with the Hood facing fold line.
2.3Carefully pin/clip the two layers together without over stretching the Hood. It’s also important to not over handle the Hood otherwise you may stretch the fabric.
2.6Wrong sides together, fold the Hood facing back on to the Hood so that the raw edge of the Hood meets with the line marked on the pattern piece. Use clips to hold in place.
2.7Take your drawstring cord and thread through the buttonholes from the wrong side and then tuck the cord up under the clips to keep them away from the stitching in the next step.
2.8Using a stretch twin needle in your sewing machine (or a small zigzag stitch if you don’t have a twin needle), sew the Hood facing down.
TIP – The distance in from the edge you’ll need to sew varies by size. Check how far your presser foot needs to be from the edge before you sew, then place a magnet or piece of tape on your machine so you can keep the edge of the facing lined up and stitch in a straight line.
TIP – For some sizes, you may find the bottom of the Hood facing can flip backwards while wearing it. Try it on at this point and see if it is secure. If not, either machine or hand stitch this to the top edge of the jacket.
0 . Preparation1 . Sleeve Construction1.2Press the seams towards the jacket from the wrong side of the fabric. On the right side of the fabric, press the seam again and then topstitch.
2 . Attach the cuff2.0SERGER / OVERLOCKER OPTION – We will be using a serger for this option
REGULAR SEWING MACHINE OPTION – Use an overcast stitch
- + Finishing Notes and Congratulations
Finishing Notes and Congratulations
Congratulations, your Kingston Jacket Add-On is done. Enjoy!
We would love to hear how you got on and see photos of your finished project!
Join us at our Facebook Group, tag us on Instagram, or use the hashtag #rpkingstonjacketaddon.
Thank you for using a Rebecca Page pattern.
© Copyright 2022
All Rights Reserved
Sales + Licencing InformationProject OverviewKingston Jacket Add-On
Difficulty Level = Beginner / Intermediate
There are 5 different options included in this add-on pattern. You can choose any or all of these options for your jacket. Mix and match to get the jacket you are looking for!
The back ruffle is a small change that requires no change to the original pattern, just a slight pause and add a few steps during construction.
The Hood is added in place of your collar pieces. But is compatible with all other options in the original and add-on pack.
The knit sleeves are obviously in place of all other sleeve options, but pair well with the Hood and any of the Pocket choices.
The two new Pockets include an inside Pocket and a welt Pocket. The inside Pocket is compatible with both the original inseam Pocket and the welt Pocket. The welt Pocket and the inseam Pocket do not work together. Neither additional Pocket interferes with the chest Pocket from the original pattern.
Between the original pattern and this add-on pack, there are so many choices for gorgeous jackets with beautiful construction and we can’t wait to see what you make up!
NOTE – The sewing instructions and steps are the same for all sizes (dolls, child’s, and ladies sizes).
SizingSize Range
18 in Dolls, Newborn – 12yrs, Womens 1-10, Womens Curvy 6C-15C
Size Chart
See the original Kingston Jacket pattern for the sizes available and finished garment measurements.
Finished Measurements (Inches)
See the original Kingston Jacket pattern for finished garment measurements.
Materials and ToolsYou will need the following, in addition to the listed requirements in the original Kingston Jacket pattern.
Fabric Requirements 60 inches/150 cm wide (in YARDS)
Frill
Knit Sleeve
Knit Hood
Welt Pocket
Inside Pocket
1-6
0.25
0.75
0.75
0.25
0.25
7-10
0.25
0.75
0.75
0.25
0.25
Frill Knit Sleeve Knit Hood Welt Pocket Inside Pocket 6C-11C 0.25 0.75 0.75 0.25 0.25 12C-15C 0.25 0.75 0.75 0.25 0.25 * If you are using a narrower fabric, a directional print, or a fabric with nap you may need more.
** Make sure to wash, dry, and press all fabrics before cutting out in case they shrink.You will also need:
- For optional Hood:
- 1-2 yards of shoe string, cording or other tie option.
- Grommets can be used in place of buttonholes, if desired
- Thread to match
Tools needed are listed in the original Kingston Jacket pattern.
- For optional Hood: